NiChrome Coils and wicks for Rebuidable Atomizers /with non resistance heat welded wire leads
Prewound NiChrome coils with heat welded non resistive extension leads. The extension leads are made from Nickel wire which allows the joint to be heat welded and NOT soldered. These are ready to install in almost any rebuidable atomizer. These coils are made from high quality 80/20 NiChrome wire and are available with a single 2.5mm x 140mm long wick or 2x 1.5mm x 140mm long wicks. Each coil is wrapped in a set resistance (1.0,1.5, 2.0,2.5,3.0,3.5) with long non resistive leads for easy connection. The wicks can easily be pulled out from the coils and replaced with a wicking diamter of your choice or cotton wicking.
Each package includes 5 pre-wound coils and wicks
1x 2.5mm wick or 2x 1.5mm wick
1.0 ohm (.24mm) (may show as .8ohm in product selection)
1.5 ohm (.24mm)
2.0 ohm (.20mm
2.5 ohm (.20mm)
3.0 ohm (.18mm)
3.5 ohm (.18mm)
Posted by Abimael on 13th Mar 2014
I own an Ithaka atty. I dont have all the zapper (wire welder0 needed to make my non resistance/resistance coils. Did a search and found Avidvaper. Tremendous deal on the coils I needed, were at my doorstep in a few days, the packaging was great and the product was on point. Im very satisfied with Avid Vaper, I will be stopping back for all my vaping needs.
Posted by Unknown on 26th Jan 2014
they worked great in my ismoka msgoo
Posted by Frank Germano on 5th Dec 2013
These are awesome when they don't fry off when first energized. Simple. Effective. Cheap. Much easier than joining non resistance to resistance wire for the Ithaka or other similar RBA's. Buy them... very good deal.
Posted by FRANK GERMANO on 28th Nov 2013
These are simple, great little convenient pre wound coils, particularly for the Golden Greek Ithaka or the clones. Pop them on and you're good to go, quickly. But - be warned, these pre wounds are iffy at best - I've ordered quite a few packs of these, and on average, two or three out of each five-pack will fry when energized. The joint where the non resistance meets the resistance will either fry or just fall off. When they are good - they are great. Just keep in mind you will probably have a number of them that are useless.
Posted by Wayne Kairdolf on 3rd Oct 2013
I have tried many many different coils and wire and wick and these are the only ones that do not taste funny when you first put them in. I am ordering more and you should too!
Posted by FRANK GERMANO on 28th Sep 2013
These little coils are fantastic. If you're in a hurry or just don't have the inclination to join non resistance wire to resistance... these work great. We should request they carry EcoWool and Kanthal resistance, but, for the price, can't beat it... good product.
Posted by Unknown on 23rd May 2013
Worked as advertised in my terminator , no fuss , easy to replace and get back to vaping . Quick ship too .
Posted by JimboSTi04 on 23rd May 2013
ordered on sunday, shipped on monday, recieved on wednesday. thats NY to CA in 3 days! threw theses on my ithaka and they are awesome!
Posted by Volcanic on 12th May 2013
I have been able to get extra mileage out of these wicks and coils by cutting the wick in half. When the coil becomes too built up, I gently uncoil, clean between the R and NR wires and recoil the wire onto the leftover half of the wick. (recycling a third time usually does not work, as the wire is weak by then) $1.39/coil sure beats $2.59 for replacement Stone attys, if you can find any. Recycling twice cuts the price per each to around $.70. This is a great product at a good price.
Posted by Vfx on 2nd May 2013
been practicing wrapping my own coils but still getting hot spots and different resistance readings. A few of my rebuildable attys are left unused and empty. So, in the meantime, im using these preassembled coils. Im usings the 3mm wick @2.5 ohm...they are reading around 2.3ohm and the wick is a bit thick, but otherwise all is fine. I will use what's left as, last minute backups. Great deal, will recommend to others!
Posted by Unknown on 28th Mar 2013
Using these in my vivi nova tanks and they work great. The wicking is phenomenal. They ohm out where they should, Easy to work with and the price is right. Awesome product.
Posted by Dan Lugo on 17th Mar 2013
Super coils, use them in my Terninator C and my Cody Atomizers. Sure makes using these attys easy. Shipping was fast also.
Posted by Unknown on 10th Mar 2013
Once the wick has been properly trimmed, and hotspots have been eliminated, these coils perform wonderfully! Wick length is crucial with these, as a wick too long or too short will result in a burning taste.
Posted by Ryan on 7th Mar 2013
Picked up two packs in 2.0ohm, 3mm wick. These are perfect for my DripperPro by Leo. The wick's need to be trimmed a bit for the Dripper, but dang...these coils hit like a choo choo train on steroids.
I knew there would be a variance in resistance, and I was right. +/-.2 ohm's seems to be the case here. I'm seeing 1.7 - 1.9 ohm's on my ProVari, running at 3.7 - 3.9 volts.
Non-resistant leads are the way to go!! Amazing taste and amazing vapor!!! Thank you Avid!!!
Posted by Jana on 30th Oct 2012
Finally I found a new coils for my Penelope ! It's impossible to get them here in Italy. They are easy to use. Work great, after few drags comes out a full pure fantastic flavor . The extension leads are a little bit short for the Penelope but if you use a tweezers you can make it. Thank you very much Avid Vaper !
Posted by CoyoteRed on 16th Oct 2012
This was the perfect solution for use on a Penelope.I admit I still want to learn how to make proper wick and coil on my own, but as many know it takes time and patience. I now can use my device and continue to learn.The ability to choose what Ohm's you want is also a plus.Another vendor sale the premade resistance-non resistance wire and charges about a buck apiece. These are slightly more and come with the wick already installed.
Choose a currency below to display product prices in the selected currency.