Single piece NiChrome Coils and wicks for Rebuidable Atomizers
Prewound NiChrome coils with extended leads are ready to install in almost any rebuidable atomizer. These coils are made from high quality 80/20 NiChrome wire wrapped around a single piece of 2mm/2.5mm Silica thread. Each coil is wrapped in a set resistance (.8/1.5, 2.0,2.5,3.0,3.5) with long leads for easy connection. These can be unwound to fine tune your final resistance.
Each package includes 5 pre-wound coils and wicks
0.8 ohm (.24mm)
1.5 ohm (.24mm)
2.0 ohm (.20mm
2.5 ohm (.20mm)
3.0 ohm (.18mm)
3.5 ohm (.18mm)
Showing reviews 1-25 of 27 | Next
Posted by SheVapes on 4th Jul 2015
These were exactly what I needed to do my first practice builds. They metered out as marked and I hope one day to be as predictable with my own wraps. I may have unfairly taken off a star because the wires snapped on all when I tightened the post screws. I'm not sure if that was due to my newness, the gauge of the wire or the phase of the moon. This means I quickly ran through them and now I know to double up on my orders. The wind is so secure I was unable (or maybe I was too scared to try) to replace the wick with cotton. The vape was great, however.
Posted by Bayless on 19th Feb 2015
These are very easy and handy. I just remove the wick and use Japanese Cotton.
Great for those times you just don't want to fiddle with wrapping.
Posted by John on 10th Nov 2014
Got these cause I am a newbie. Easy to install, ohm are little higher than advertised. Work like a charm.
Posted by C D on 15th May 2014
I purchased a set of the 2 ohm and 2.5 ohm coils to test out. The coils are built well and have plenty of extra lead to add more wraps or take some out if you want to change the resistance. I tested the resistances of the coils out of the bag and they are all very close to advertised. I initially bought these for my V-core tank because of the small area for the coils is too hard to wrap your own. These are perfect for that. I also gave these a shot in my KayFun tank. Not disappointed at all. I typically prefer cotton, but the silica that comes on these isn't too bad. I did swap the silica for cotton on the KayFun though. I will be a returning customer. Nice product, nice price and really fast purchase to delivery time.
Posted by Ed on 18th Apr 2014
Great little coils with good wick.
Posted by Vapolith on 9th Oct 2013
I wrap my own coils most of the time, but these prewrapped coils are terrific for when I'm in a hurry, and want to get one of my Reomizer 2s up and running quick! I use cotton wicks, so I put the silica wicks that come with these in a ziplock bag in case I ever want to use silica.
Posted by Andy on 30th Sep 2013
Wick is nice and clean and enough length to rebuild anything I have. Works perfectly. Pre made coils, what a convenience, and a fair price.
Posted by _more_ using a REO on 5th Sep 2013
I use these coils on a reomizer2 rba. Works great every time.
Posted by Unknown on 22nd Aug 2013
This product works great.
Posted by Unknown on 13th Aug 2013
These coils are excellent, all my wraps have performed wonderfully at 2.0ohms or above!
Posted by Unknown on 22nd Jun 2013
Having arthritis this was perfect not having to wrap my own coils and also having the different Ω choices.
Posted by Unknown on 18th Jun 2013
Super easy to rebuild with these just pop them in and go. My first one was at 1.7 ohms and I oredered 1.5. not so much a big deal.
Posted by Jason on 24th May 2013
I bought a few "entry level" RBA's, the Phoenix V4 and the Igo-L, and was unsure about wrapping my own coils at first. These come ready to install which at least got me up and running on my new gear, awesome. I bought 1.5 and 2.0ohm versions and all 10 coils metered out at listed resistance +/- .1ohms. The wicks and coil leads are long enough for any post spacing gaps you'll run into. I used the leftover wick and wire to start rolling my own coils for practice. A week later I am rolling my own coils like a champ. Buy these with confidence.
Posted by HauntedMyst on 9th May 2013
Easy to install, well rolled. These are awesome for the price and work well in a Kanger ProTank.
Posted by Bryan on 2nd May 2013
This item is saving me money buy doing it myself
Posted by lotulle Eustace on 1st Mar 2013
I'm a RBA newbie. These are easy to install and work great with little or no hotspots. Best vapes of my life!
Posted by Unknown on 27th Feb 2013
I ordered 1 pack of 2.0 ohm and 3 packs of 2.5 ohm coils. on the 2.0 pack they metered at 2.4 so I had to play with removing coils to get the right resistance and the wicks were super long (enough for 2 coils worth), while on the 3 packs of 2.5ohms I ordered they are metering at nearly 3 ohms (about 2.9) and the wicks are so short that they are about half the length of a standard v3 stardust wick size. So that leaves me unwrapping coils to reach the resistance I thought I was ordering pre-made because I did not want to be wrapping my own wicks at this point in time. I'm new to vaping and just starting out with rebuilding and this was my first shot as this, so I guess I am jumping in a little deeper than I had intended to. These should really come with more consistent wick lengths (they were huge on the 2.0 and tiny on the 2.5) and they should meter correctly as they come and not have to cause guesswork to get the stated ohmage. I could understand a slight variation but nearly a whole .5 ohm off is a lot.
Posted by Jaybo on 27th Jan 2013
Works well. I remove a turn in the coil for better performance, 3 Ohms to 2.8 Ohms.
The wicks could be longer to reach lower into the tank. They are easily cut and this would help a lot for all users IMO.
Posted by Michael Chirco on 29th Oct 2012
easy to install work great with any pv
Posted by Michael Chirco on 9th Oct 2012
got these in 1.5 ohm and their great for my vivi's and work great on my 3.7 devices also good for my vv device
Posted by travis from utah on 13th Sep 2012
got them in and the wics were small butt the coils are nice and round
Posted by travis linger on 11th Sep 2012
the coils are exlent but the wic neads to b longer i got t cets of them butt wont work becuse the wic is 2 short
Posted by Matt on 27th Aug 2012
Insanely easy to install with the extra wire provided off the coils. Wicks are pre-cut to the perfect size, plenty of wick material to fluff into the cup on my Phoenix Bully RA. The resistance metered out at 1.95 ohms. I ordered the 2.0 ohm coils so +/-0.05 is totally fine by me. Very accurate. Saves a bunch of time wrapping your own coils trying to get the resistance you want. Well done at a great price!
Posted by Mike on 15th Aug 2012
I use them to rebuild Vivi Nova atty heads. Works great. Got the higher resistance and just unwound a little bit. Now I can push my Vivi up to 6V. Yay.
Posted by Unknown on 11th Aug 2012
Installing the coil in my vivi nova was easy. My 2.9 coil does meter out to 3.3 on my provari but that's alright. At first I didn't get much flavor and was disappointed but after vaping it for awhile, the flavor has really come through! It has been going strong for several days now and I couldn't be happier!
Showing reviews 1-25 of 27 | Next
Choose a currency below to display product prices in the selected currency.